The Gameboy Advance Overclocker Flex from Robot_Retro allows for easy overclocking or underclocking of your device. With a streamlined installation process that eliminates the need for manual wiring (except for an optional LED indicator wire), this mod makes it simple to customize your gaming experience.
FEATURES:
Capable of over and underclocking to 30%, 50%, 75%, 130%, 150% or 170% of base clock.
Easy flex installation with optional wire link to LED DL2A. Power LED will blink faster when overclocked and slower when underclocked. Base speed is a solid green LED.
Very low power consumption. Measured as <15mA using the Nordic Power Profiler Kit II.
Accurate base clock (4.194Mhz). Measured as >0.01% accurate. There is will no difference between this mod and the original GBA crystal at stock speeds.
Remove the GBA crystal. Recommended to use a hot air station for this step.
Install the flex as per photos. Solder the points shown within the pink circles (total of 6 solder points). It is recommended to use flux for this step.
OPTIONAL: Run and wire between the flex and test point DL2A (both shown inside the yellow circles). This will make the power LED blink faster/slower when over or underclocking.
Speed Limiting
Bridge solder jumper S1 to limit the speed to 150%.
Bridge solder jumper S2 to limit the speed to 130%.
Increase speed = Press Start and Up
Decease speed = Press Start and Right
The regular install has a maximum speed of 170%. This is suitable for the stock LCD, Funnyplaying v2 or Hispeedido v2 (non-laminated) kits.
If using the Hispeedido Laminated v5, bridge solder jumper S1 to limit the speed to 150%.
If using Funnyplaying 3.0 Inch and ITA Laminated, bridge solder jumper S2 to limit the speed to 130%.
Price: $22.06 | Category: repaired | Maker: handheldlegend" />
The Gameboy Advance Overclocker Flex from Robot_Retro allows for easy overclocking or underclocking of your device. With a streamlined installation process that eliminates the need for manual wiring (except for an optional LED indicator wire), this mod makes it simple to customize your gaming experience.
FEATURES:
Capable of over and underclocking to 30%, 50%, 75%, 130%, 150% or 170% of base clock.
Easy flex installation with optional wire link to LED DL2A. Power LED will blink faster when overclocked and slower when underclocked. Base speed is a solid green LED.
Very low power consumption. Measured as <15mA using the Nordic Power Profiler Kit II.
Accurate base clock (4.194Mhz). Measured as >0.01% accurate. There is will no difference between this mod and the original GBA crystal at stock speeds.
Remove the GBA crystal. Recommended to use a hot air station for this step.
Install the flex as per photos. Solder the points shown within the pink circles (total of 6 solder points). It is recommended to use flux for this step.
OPTIONAL: Run and wire between the flex and test point DL2A (both shown inside the yellow circles). This will make the power LED blink faster/slower when over or underclocking.
Speed Limiting
Bridge solder jumper S1 to limit the speed to 150%.
Bridge solder jumper S2 to limit the speed to 130%.
Increase speed = Press Start and Up
Decease speed = Press Start and Right
The regular install has a maximum speed of 170%. This is suitable for the stock LCD, Funnyplaying v2 or Hispeedido v2 (non-laminated) kits.
If using the Hispeedido Laminated v5, bridge solder jumper S1 to limit the speed to 150%.
If using Funnyplaying 3.0 Inch and ITA Laminated, bridge solder jumper S2 to limit the speed to 130%.
Price: $22.06 | Category: repaired | Maker: handheldlegend" />
The Gameboy Advance Overclocker Flex from Robot_Retro allows for easy overclocking or underclocking of your device. With a streamlined installation process that eliminates the need for manual wiring (except for an optional LED indicator wire), this mod makes it simple to customize your gaming experience.
FEATURES:
Capable of over and underclocking to 30%, 50%, 75%, 130%, 150% or 170% of base clock.
Easy flex installation with optional wire link to LED DL2A. Power LED will blink faster when overclocked and slower when underclocked. Base speed is a solid green LED.
Very low power consumption. Measured as <15mA using the Nordic Power Profiler Kit II.
Accurate base clock (4.194Mhz). Measured as >0.01% accurate. There is will no difference between this mod and the original GBA crystal at stock speeds.
Remove the GBA crystal. Recommended to use a hot air station for this step.
Install the flex as per photos. Solder the points shown within the pink circles (total of 6 solder points). It is recommended to use flux for this step.
OPTIONAL: Run and wire between the flex and test point DL2A (both shown inside the yellow circles). This will make the power LED blink faster/slower when over or underclocking.
Speed Limiting
Bridge solder jumper S1 to limit the speed to 150%.
Bridge solder jumper S2 to limit the speed to 130%.
Increase speed = Press Start and Up
Decease speed = Press Start and Right
The regular install has a maximum speed of 170%. This is suitable for the stock LCD, Funnyplaying v2 or Hispeedido v2 (non-laminated) kits.
If using the Hispeedido Laminated v5, bridge solder jumper S1 to limit the speed to 150%.
If using Funnyplaying 3.0 Inch and ITA Laminated, bridge solder jumper S2 to limit the speed to 130%.